5 Tips To Speed Up Linux Software Raid Rebuilding And Re-syncing

http://www.cyberciti.biz/tips/linux-raid-increase-resync-rebuild-speed.html


It is no secret that I am a pretty big fan of excellent Linux Software RAID. Creating, assembling and rebuilding small array is fine. But, things started to get nasty when you try to rebuild or re-sync large size array. You may get frustrated when you see it is going to take 22 hours to rebuild the array. You can always increase the speed of Linux Software RAID 0/1/5/6 reconstruction using the following five tips.

Recently, I build a small NAS server running Linux for one my client with 5 x 2TB disks in RAID 6 configuration for all in one backup server for Mac OS X and Windows XP/Vista client computers. Next, I cat /proc/mdstat and it reported that md0 is active and recovery is in progress. The recovery speed was around 4000K/sec and will complete in approximately in 22 hours. I wanted to finish this early.

Tip #1: /proc/sys/dev/raid/{speed_limit_max,speed_limit_min} kernel variables

The /proc/sys/dev/raid/speed_limit_min is config file that reflects the current "goal" rebuild speed for times when non-rebuild activity is current on an array. The speed is in Kibibytes per second (1 kibibyte = 2¹⁰ bytes = 1024 bytes), and is a per-device rate, not a per-array rate . The default is 1000.
The /proc/sys/dev/raid/speed_limit_max is config file that reflects the current "goal" rebuild speed for times when no non-rebuild activity is current on an array. The default is 100,000.
To see current limits, enter:
# sysctl dev.raid.speed_limit_min
# sysctl dev.raid.speed_limit_max
To increase speed, enter:

 
echo value > /proc/sys/dev/raid/speed_limit_min
 

OR

 
sysctl -w dev.raid.speed_limit_min=value
 

In this example, set it to 50000 K/Sec, enter:
# echo 50000 > /proc/sys/dev/raid/speed_limit_min
OR
# sysctl -w dev.raid.speed_limit_min=50000
If you want to override the defaults you could add these two lines to /etc/sysctl.conf:

#################NOTE ################
##  You are limited by CPU and memory too #
###########################################
dev.raid.speed_limit_min = 50000
## good for 4-5 disks based array ##
dev.raid.speed_limit_max = 2000000
## good for large 6-12 disks based array ###
dev.raid.speed_limit_max = 5000000

Tip #2: Set read-ahead option

Set readahead (in 512-byte sectors) per raid device. The syntax is:
# blockdev --setra 65536 /dev/mdX
## Set read-ahead to 32 MiB ##
# blockdev --setra 65536 /dev/md0
# blockdev --setra 65536 /dev/md1

Tip #3: Set stripe-cache_size for RAID5 or RAID 6

This is only available on RAID5 and RAID6 and boost sync performance by 3-6 times. It records the size (in pages per device) of the stripe cache which is used for synchronising all write operations to the array and all read operations if the array is degraded. The default is 256. Valid values are 17 to 32768. Increasing this number can increase performance in some situations, at some cost in system memory. Note, setting this value too high can result in an "out of memory" condition for the system. Use the following formula:

memory_consumed = system_page_size * nr_disks * stripe_cache_size

To set stripe_cache_size to 16 MiB for /dev/md0, type:
# echo 16384 > /sys/block/md0/md/stripe_cache_size
To set stripe_cache_size to 32 MiB for /dev/md3, type:
# echo 32768 > /sys/block/md3/md/stripe_cache_size

Tip #4: Disable NCQ on all disks

The following will disable NCQ on /dev/sda,/dev/sdb,..,/dev/sde using bash for loop

 
for i in sd[abcde]
do
  echo 1 > /sys/block/$i/device/queue_depth
done
 

Tip #5: Bitmap Option

Bitmaps optimize rebuild time after a crash, or after removing and re-adding a device. Turn it on by typing the following command:
# mdadm --grow --bitmap=internal /dev/md0
Once array rebuild or fully synced, disable bitmaps:
# mdadm --grow --bitmap=none /dev/md0

Results

My speed went from 4k to 51k:
cat /proc/mdstat
Sample outputs:

Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath]
md5 : active raid1 sde2[2](S) sdd2[3](S) sdc2[4](S) sdb2[1] sda2[0]
      530048 blocks [2/2] [UU]
md0 : active raid6 sde3[4] sdd3[3] sdc3[2] sdb3[1] sda3[0]
      5855836800 blocks level 6, 64k chunk, algorithm 2 [5/5] [UUUUU]
      [============>........]  resync = 61.7% (1205475036/1951945600) finish=242.9min speed=51204K/sec

Monitoring raid rebuilding/recovery process like a pro

You cat /proc/mdstat file. This read-only file contains information about the status of currently running array and shows rebuilding speed:
# cat /proc/mdstat
Alternatively use the watch command to display /proc/mdstat output on screen repeatedly, type:
# watch -n1 cat /proc/mdstat
Sample outputs:

The following command provide details about /dev/md2 raid arrray including status and health report:
# mdadm --detail /dev/md2
Sample outputs:

Another option is to see what is actually happening by typing the following iostat command to see disk utilization:

 
watch iostat -k 1 2
watch -n1 iostat -k 1 2
 

Sample outputs:

References:

• See man pages - md(4), mdadm(8)

TERIMA KASIH ATAS KUNJUNGAN SAUDARA
Semoga artikel ini bermanfaat bagi saudara. Jika ingin mengutip, baik itu sebagian atau keseluruhan dari isi artikel ini harap menyertakan link dofollow ke http://androidjapane.blogspot.com/2013/06/5-tips-to-speed-up-linux-software-raid.html. Terima kasih sudah singgah membaca artikel ini.